Hydraulic

A strange hydraulics problem - but true!

A few months ago, I was involved - in a supervisory capacity - in the planned change out of components on a hydraulic machine.

The design of the machine's hydraulic power unit was the all-too-common, cheap and nasty, everything mounted on the tank lid variety. You know the ones - electric motors mounted vertically, with pumps submerged in the tank. They're cheap and easy to build, but an eternal pain in the butt for anyone who has to work on them. I could rant about this … but I'll save it for another day.

The scope of work included changing out a tandem gear pump submerged in the tank. On this machine, a 15 minute job - after you've spent two hours disconnecting everything to enable the tank lid to be lifted.

I was offsite when this pump was changed, but the technician doing the work was experienced and knew what had to be done. After the shut down was completed, the same technician was scheduled to re-commission the machine. But due to conflicting commitments he became unavailable.

It was early in the afternoon when I got the call requesting I go to site to supervise start-up. Thinking this would be a case of push the button and watch everything behave as it should, I left the office in my 'civilian' clothes, took my good car and no tools. BAD mistake.

Commissioning didn't begin well. The rear section of the tandem gear pump that had been replaced, charged an accumulator. But we weren't getting any charge pressure on start-up. The direction of rotation of the electric motor was correct. But what about the rotation of the new pump? Bit hard to tell when it's submerged in the tank.

After speaking with the technician on my cell, I was reasonably confident the new pump's rotation was correct. But just to be sure, I decided to try reversing the rotation of the electric motor. No change.

Now what? I don't have a flow-tester with me and it's a major job to lift the tank lid. It appears that new pump is either faulty or not priming. Unlike a vane pump which needs a head of oil on its outlet for the vanes to 'throw' and start pumping, a gear pump is normally considered self-priming - especially when its submerged in hydraulic oil.

To give the new pump the best possible chance of priming, I topped off the oil level at maximum. Still no charge pressure after running for a minute. In the absence of a flow-meter, I decided to lift the electric motor off its bell housing, disconnect the pipes from the pump's outlet penetrations in the top of the tank and turn the pump by hand.

This was revealing. The front section was pumping, but the rear section wasn't. Joy. The rear section was faulty. I continued turning the pump by hand, while I wondered what the chances were of this happening, and contemplated the work involved in lifting the tank lid.

Just as I was about to give up and call for reinforcements, I noticed oil was being displaced from the rear pump's outlet penetration in the top of the tank. It WAS pumping. I reconnected the plumbing, dropped the electric motor back into position and bingo. We had accumulator charge.

Had I been told this story about a gear pump that wouldn't prime itself - I would have struggled to believe it. Yes it IS strange … but true.

If you enjoyed this article, you'll love Brendan Casey's Inside Hydraulics newsletter. It gives you real-life, how-to-do-it, nuts-and-bolts, hydraulics know-how – information you can use today. Listen to what a few of his subscribers have to say:

Can't Put It Down
“I get magazines and e-mails like this all the time. I never find time to read them. I decided to read Issue #30 and I couldn't put it down. I'll make time from now on.”

Richard A. Shade, CFPS
Project Engineer (Hydraulic Design)
JLG Industries Inc.

So Valuable It Earned Me A Raise
“The knowledge I've gained from this newsletter has been so valuable it has earned me a raise!”

Jack Bergstrom
Heavy Equipment Mechanic
Sharpe Equipment Inc.

Love It - Keep Them Coming
“I just love this newsletter. As a Hydraulics Instructor for Eaton, I make copies and distribute them to my students as I address various topics... Keep 'em coming.”

Michael S Lawrence
Hydraulics Instructor
Eaton Hydraulics Inc.

Here's a sample of what's covered in this powerful newsletter: troubleshooting, contamination control, component repair and testing, preventative maintenance, failure analysis, and much, much more!

To get a FREE subscription to the Inside Hydraulics newsletter, fill out this form - don't forget to capitalize the first letter of your name - and hit 'SUBSCRIBE NOW!'

First Name *
Email *

This is a private mailing list that will never be sold or given away for any reason.
You can also unsubscribe at anytime.


[Home]


Copyright © 2002 - 2013 Brendan Casey; Insider Secrets to Hydraulics