Hydraulic fitting

Hydraulic fitting selection the key to leak-free hydraulic plumbing

Hydraulic fitting leaks are often considered to be an inherent characteristic of hydraulic machines. While this may have been true 30 years ago, advances in sealing technology and the development of reliable connection systems means that today, leak-free hydraulic plumbing is readily achievable.

Reliable Connections

Leak-free reliability begins at the design stage, when the type of hydraulic fitting is selected for port, tube-end and hose-end connections.

Ports - Connectors that incorporate an elastomeric seal such as UNO, BSPP and SAE 4-bolt flange offer the highest seal reliability. NPT is the least reliable type of connector for high-pressure hydraulic systems because the thread itself provides a leak path. The threads are deformed when tightened and as a result, any subsequent loosening or tightening increases the potential for leaks. In existing systems, pipe thread connections should be replaced with UNO or BSPP for leak-free reliability.

Tube and Hose Ends - ORFS tube and hose end connections feature the high seal reliability afforded by an elastomeric seal but, due to its cost, ORFS is not as widely used as compression fittings and JIC 37-degree flare.

Flared connections have gained widespread acceptance due to their simplicity and low cost. However, the metal-to-metal seal of the flare means that a permanent, leak-free joint is not always achieved, particularly in the case of tube-end connections.

Leaking flare joints can be eliminated using a purpose-built seal developed by Flaretite. The Flaretite seal is a stainless steel stamping shaped like a JIC nose, with concentric ribs that contain pre-applied sealant. When tightened, the ribs crush between the two faces of the joint, eliminating any misalignment and surface imperfections. The combination of the crush on the ribs and the sealant ensure that a leak-free joint is achieved.

Incorrect Torque

A common cause of leaks from flare joints is incorrect torque. Insufficient torque results in inadequate seat contact, while excessive torque can result in damage to the tube and fitting through cold working. The following is a simple method to ensure flare joints are correctly torqued:

  1. Finger tighten the nut until it bottoms on the seat.
  2. Using a permanent marker, draw a line lengthwise across the nut and fitting.
  3. Wrench tighten the nut until it has been rotated the number of hex flats listed in the following table:
Tube Dash SizeHex Flats
42.5
52.5
62.0
82.0
101.5 - 2.0
121.0
160.75 - 1.0
200.75 - 1.0
240.5 - 0.75

Vibration

Vibration can stress plumbing, affecting hydraulic fitting torque and causing fatigue. Tube is more susceptible than hose. If vibration is excessive, the root cause should be addressed. Ensure all conductors are adequately supported and if necessary, replace problematic tubes with hose.

Seal Damage

Having outlined the benefits of hydraulic fittings that incorporate an elastomeric seal, it is important to note that their reliability is contingent on fluid temperature being maintained within acceptable limits. A single over-temperature event of sufficient magnitude can damage all the seals in a hydraulic system, resulting in numerous leaks.

Conclusion

A leak-free hydraulic system should be considered the norm for modern hydraulic machines - not the exception. But the proper selection, installation and maintenance of hydraulic plumbing are essential to ensure leak-free reliability.

If you enjoyed this article, you'll love Brendan Casey's Inside Hydraulics newsletter. It gives you real-life, how-to-do-it, nuts-and-bolts, hydraulics know-how – information you can use today. Listen to what a few of his subscribers have to say:

Can't Put It Down
“I get magazines and e-mails like this all the time. I never find time to read them. I decided to read Issue #30 and I couldn't put it down. I'll make time from now on.”

Richard A. Shade, CFPS
Project Engineer (Hydraulic Design)
JLG Industries Inc.

So Valuable It Earned Me A Raise
“The knowledge I've gained from this newsletter has been so valuable it has earned me a raise!”

Jack Bergstrom
Heavy Equipment Mechanic
Sharpe Equipment Inc.

Love It - Keep Them Coming
“I just love this newsletter. As a Hydraulics Instructor for Eaton, I make copies and distribute them to my students as I address various topics... Keep 'em coming.”

Michael S Lawrence
Hydraulics Instructor
Eaton Hydraulics Inc.

Here's a sample of what's covered in this powerful newsletter: troubleshooting, contamination control, component repair and testing, preventative maintenance, failure analysis, and much, much more!

To get a FREE subscription to the Inside Hydraulics newsletter, fill out this form - don't forget to capitalize the first letter of your name - and hit 'SUBSCRIBE NOW!'

First Name *
Email *

This is a private mailing list that will never be sold or given away for any reason.
You can also unsubscribe at anytime.



[Home]


Copyright © 2002 - 2013 Brendan Casey; Insider Secrets to Hydraulics